Water-SIL-PD Waterproofer – 5 Gallon

Water-SIL-PD is a pre-diluted, ready-to-use waterborne multi surface water repellent.  Water-SIL-PD is a solvent-free penetrating product that provides long-term water repellency and protection to most masonry and wood substrates and is safe to spray around grass and other landscape plantings and water features.

 

Request Pricing/Sample

 

 

       

SKU: EASIL640PD Category:

Description

Details

Water-SIL-PD is a pre-diluted, ready-to-use waterborne multi surface water repellent.  Water-SIL-PD is a solvent-free penetrating product that provides long-term water repellency and protection to most masonry and wood substrates and does not damage glass or metal surfaces.  This low-odor formula is also perfectly safe to spray around grass and other landscape plantings and water features.  Water-SIL-PD is a vapor permeable repellent that allows the substrate to continue to exchange gases with the environment.  This is most beneficial when applying to new or damp construction surfaces.

 

Product Details

Product Use Concrete, Brick , Stone, Stucco, Exterior Wood, EIFS, Pavers
Coverage Approximately 240 sq/ft per Gallon
Finish / Sheen Natural
Dry Time 1 to 2 hours
Algae, Mold, Mildew Resistant Yes
Base Material Water-Based
Application Temp 34F to 100F
Application Method Airless Sprayer
Clean Up Soap & Water
VOC Level <10 g/l
Flammable No
Warranty Limited 10-Year

 

Material …Approx Coverage per diluted Gallon
Concrete Smooth ……………… 300 – 400
Concrete Block Lt.Wt. ………… 75 – 150
Sand Block Cast Stone ………. 200 – 300
Brick Porous ……………………… 150 – 200
Stucco Smooth Finish ……….. 150 – 200
Wood Porous ……………………. 200 – 250
Concrete Textured ……………. 200 – 300
Concrete Block Dense ………. 150 – 200
Sandstone ………………………… 150 – 200
Brick Dense ………………………. 300 – 350
Stucco Rough Finish …………. 100 – 150
Wood Dense ……………………… 300 – 380

Features

  • Prevents water damage, mold and mildew
  • Vapor Permeable – does not trap moisture
  • Can be applied when substrate moisture level is up to 25%
  • Protects surface against de-icing salts & chemicals
  • VOC Compliant
  • Alkaline Stable – safe for use on new concrete
  • Easy to Mix Concentrate – makes up to 19 gallons of water repellent
  • Can be used in cold temperatures (above 35˚ F)
  • Prevents Efflorescene
  • Meets USDA specifications for use in food processing areas
  • Dries completely clear / non-yellowing
  • Resistant to UV degradation allowing for long-term protection
  • Provides abrasion resistance to resist wear on substrates
  • Exceeds federal specifications for water repellency on masonry, brick, wood, and other construction materials

Directions

Preparing Surface

 Before applying Water-SIL-PD all surfaces should be clean and free from dust, dirt, oils, grease, curing compounds, coatings, mildew, mold, algae, other water repellents or any other contaminants.  If efflorescence (white residue) is present, wash surface with cleaner and / or pressurized water.  Rinse any cleaning product thoroughly from the substrate and allow to reach at least 20% dryness before applying Water-SIL-48.  Application to a dry surface is preferred to facilitate maximum penetration for optimum performance but a damp (not saturated) surface will yield desired results as well.  Wood and masonry surfaces may be cleaned by any agreeable method such as:  Power wash, sweep, deck cleaners, stain removers / strippers.

How to Apply

Water-SIL-PD is pre-diluted and ready to use so no additional dilution is necessary for application to masonry and cementious substrates.  If applying to exterior wood, Water-SIL-PD may be diluted 1:1 with clean water.

Apply Water-SIL-PD using low pressure spray equipment.  To avoid atomizing product, use a spray tip size of .035 to .051.  Water-SIL-PD can also be applied with a brush, roller, or mop but spraying is recommended.

Apply uniformly and avoid over-application.  Heavy runs and drips should be thoroughly brushed into the surface.  On extremely porous substrates, two applications will provide super application.

For interior applications it might be necessary to scrub floors after the product dries to remove any excess material from the surface that might cause slickness.

Apply the second coat immediately after the first coat has penetrated.  Control application so that the second coat is applied within a few minutes after the first coat appears dry.

Thoroughly wash all equipmant and clothing after use.  Application equipment may be cleaned with soap and water.  Also, clean any unwanted overspray immediately with water.  A cleaner may be needed but water should be enought to wash product off of glass, metal, etc.

**NOTE:  THIS PRODUCT CONTAINS AN ADDITIVE THAT ALLOWS IT TO BE MIXED WITH WATER WITHOUT THE NEED FOR HARSH SOLVENTS.  AFTER APPLICATION THE SURFACTANT SLOWLY BEGINS TO LEAVE THE SUBSTRATE AND CAN TAKE SEVERAL WEEKS TO BE COMPLETELY EXPELLED.  THE PERFORMANCE OF THIS PRODUCT WILL INCREASE AS THE SURFACTANT IS RELEASED.**

Additional information

Product Use

Brick, Concrete, EIFS, Exterior Wood, Pavers, Stone

Finish/Sheen

Natural

Application Method

Brush, Roller, Sprayer